CALL US
0086-371-60922096

Concrete pumping prediction considering different measurement of

Prediction of Concrete Pumping: Part II-Analytical

Request PDF | Prediction of Concrete Pumping: Part II-Analytical Prediction and Experimental Verification | The primary objective of this study is to verify if the rheological properties of the

Learn More

TOTAL HEAD, N.P.S.H. AND OTHER CALCULATION …

3. Calculate the specific speed and predict the pump efficiency. Calculate the suction specific speed and Thoma number and check the prediction of the Thoma number regarding cavitation. 4. Calculate the temperature rise of the fluid within the pump and compare with the maximum recommended. 5.

Learn More

Comparative Study of the Abrasion Resistance

A series of concrete mixes were prepared and tested in the laboratory installations at Purdue University Calumet to determine which mix would show higher resistance to abrasion. Tests were performed during summer and fall of 2007 on 16 mixes with two finishing conditions. This investigation included preliminary testing on three different mixes.

Learn More

Project Management for Construction: Cost Estimation

Cost estimating is one of the most important steps in project management. A cost estimate establishes the base line of the project cost at different stages of development of the project. A cost estimate at a given stage of project development represents a prediction provided by the cost engineer or estimator on the basis of available data.

Learn More

Iron Loss Prediction Model for Radial Magnetic Bearing of

Oct 10, 2018 · Abstract: In this paper, an iron loss prediction model of magnetic bearing considering temperature influence is proposed. A ring specimen test under different frequencies, flux densities and temperatures is used to measure iron loss of steel laminations. Then, an iron loss model with variable coefficients is used for iron loss calculation of the magnetic bearing.

Learn More

CRACK WIDTH CALCULATION METHODS FOR LARGE …

The blocks were made of different concrete mixes and had various reinforcements and concrete cover. Tests on 3 blocks subject to restrained shrinkage RG1 to RG3 (6,00 m 0,50 m 0,80 m), with different reinforcement and concrete cover. Tests on 6 concrete blocks at 1/3 scale under continuous loading (1,90 m 0,25 m 0,44

Learn More

Pavement Manual: Rigid Pavement Design Process for CPCD

The M r of concrete is a measure of the flexural strength of the concrete as determined by breaking concrete beam test specimens. An M r of 620 psi at 28 days should be used with the current statewide specification for concrete pavement design. If the engineer selects an alternate value for M r, it must be documented with an explanation.

Learn More

One-Stop diy concrete pump Depot From Leading Sellers

60 cubic meter per hour diesel mobile concrete trailer pump for sale Our Advantages: 1. Factory directly supply over 20 years' history. As the leading concrete pump designer, manufacturer and exporter, Taian Minle Machine Manufacture Co.

Learn More

Project Management for Construction: Labor, Material and

For this purpose, it is convenient to express labor productivity as functional units per labor hour for each type of construction task. However, even for such specific purposes, different levels of measure may be used. For example, cubic yards of concrete placed per hour is a lower level of measure than miles of highway paved per hour.

Learn More

ECOLOGICAL AUC: a misleading measure of the performance …

different measurement scales (Pepe, 2000). However, in this way, transformations for species occurrence probabilities, such as those proposed by Real et al. (2006), may dramatically change the prediction output but do not have any effect on the AUC score. AUC is a discrimination index that represents the likeli-

Learn More

Durability of concrete structures in marine atmosphere

Concrete specimens with three different mix­ Considering the measurement of salt presence in atmosphere, cascade collectors [17], pumping systems [18] or simplified captur-ing systems based on deposition measurements [19,20] are com-monly employed in marine atmosphere zone with this …

Learn More

Design of Concrete Pavement for City Streets

Since the mode of failure in the design of concrete pavement is flexural fatigue, it is important that the concrete have adequate flexural strength (modulus of rupture) to resist cracking from flexural fatigue. Under average conditions the concrete should achieve a …

Learn More

Volume 19/Number 1 Control of Air Content in Concrete

Pumping Reduction in air content Use loop in descending ranges from 2 to 3%. pump line. Keep the pressure-meter method, measure the total air content only, and conse-quently provide no information about number of bubbles of different size. 1., Concrete,"

Learn More

Pipe Friction Loss Calculations

The imperial form of the Hazen-Williams formula is: hf = 0.002083 x L x (100/C)^1.85 x (gpm^1.85 / d^4.8655) where: hf = head loss in feet of water. L = length of pipe in feet. C = friction coefficient. gpm = gallons per minute (USA gallons not imperial gallons) d = inside diameter of the pipe in inches. The empirical nature of the friction

Learn More

Concrete pumping prediction considering different

May 20, 2018 · To examine the effects of different rheological measurements on predicting the pipe flow of pumped concrete, the rheological properties of bulk concrete and the lubrication layer, which are two representative pumping layers, were measured experimentally using two different measuring systems for each part and the pumping pressures were compared and verified with full scale pumping tests.

Learn More

Concrete pumping prediction considering different

This study examined the effects of different rheological measurements on predicting the concrete pumping. For two representative pumping layers in a pipe, two different measuring systems using ICAR and Contec5 for bulk concrete layer, and tribometer and Brookfield viscometer for the lubrication layer were used to determine the rheological properties.

Learn More

Monitoring the construction of a large-diameter caisson in

Dec 16, 2020 · Considering first the line A measurements, the total normal stresses and shear stresses monitored by LC 1A were lower than expected throughout construction with the exception of a peak at −15 m AOD. This LC was installed radially inwards by 20 mm from the exterior surface of the leading edge and very close to a lubrication port.

Learn More

Concrete Air Testing: An In-Depth Look - Gilson Co.

Both meters use similar methods to consolidate fresh concrete into the measuring bowl, or pot. Concrete is deposited in three equal layers, and each layer is rodded 25 times with a tamping rod. The concrete gets struck off with a strike-off bar or plate, so the volume in a given bowl is the same each time.

Learn More

What is Viscosity, and Why is Measuring Viscosity Important?

Petroleum: Viscosity measurements project the effectiveness of lubricating oil and determines design elements of pipelines. Concrete: Viscosity determines the self-leveling and pumping behavior of a mix. Cosmetics: Viscosity should be considered when designing the feel and flow of cosmetic products.

Learn More

Durability of concrete structures in marine atmosphere

Concrete specimens with three different mix­ Considering the measurement of salt presence in atmosphere, cascade collectors [17], pumping systems [18] or simplified captur-ing systems based on deposition measurements [19,20] are com-monly employed in marine atmosphere zone with this …

Learn More